Euchner AS User Manual Page 1

AS-Interface Safety at Work Quick Reference

Safety Monitors - AS-i Quick Reference - 08/2014 10 2.5 Replacing a defective Monitor 1. Separate the defective monitor completely 2. Connect n

Safety Monitors - AS-i Quick Reference - 08/2014 11 2.6 Cable pin configuration for safety monitor 235867RJ45Do not connectthe other pins!Nur die

Safety Monitors - AS-i Quick Reference - 08/2014 12 2.7 Faults shown at monitor and solution Fault shown: Fault red blinking at monitor Descriptio

Safety Monitors - AS-i Quick Reference - 08/2014 13 LEDs Reason ActionFailure on AS-iMonitor has no data transfer to masterCheck AS-i bus,setup of m

Safety Monitors - AS-i Quick Reference - 08/2014 14 3 GMOX Safety Monitor 3.1 Password forgotten or lost If the password is lost for your configu

Safety Monitors - AS-i Quick Reference - 08/2014 15 Alternative 3 (it must be a memory card in the device) 1. Press OK-button 2. Select AS-I SA

Safety Monitors - AS-i Quick Reference - 08/2014 16 If you have the 4- digit code … 1. Contact technical support at EUCHNER and enter the 4-digit

Safety Monitors - AS-i Quick Reference - 08/2014 17 3.2 Delete Safety Monitor 1. Press OK-button 2. Select AS-I SAFETY and press OK-button

Safety Monitors - AS-i Quick Reference - 08/2014 18 3.3 Slave-Address-Tool in the Safety Monitor This function enables setting and changing

Safety Monitors - AS-i Quick Reference - 08/2014 19 3.4 Replacing a defective slave (without teach-in of actuator) If an AS-i safety slave is defe

Safety Monitors - AS-i Quick Reference - 08/2014 2 Directory 1 EUCHNER Safety Parts ...

Safety Monitors - AS-i Quick Reference - 08/2014 20 3.5 Replacing a defective slave (with teach-in of actuator) If an AS-i safety slave is defecti

Safety Monitors - AS-i Quick Reference - 08/2014 21 3.6 Reset Safety Error (caused by exchange of a safety slave) When exchanging safety slaves

Safety Monitors - AS-i Quick Reference - 08/2014 22 ATTENTION: The monitor now switches all outputs off 7. Key in SLAVE ADDR of the slave to tea

Safety Monitors - AS-i Quick Reference - 08/2014 23 3.7 Replacing a defective AS-i Safety Monitor If an AS-i Safety Monitor is defective and needs

Safety Monitors - AS-i Quick Reference - 08/2014 24 3. Select SLAVE ADR TOOL and press OK-button 4. Select CARD -> MONITOR and press O

Safety Monitors - AS-i Quick Reference - 08/2014 25 3.8 Set outputs of the slaves With this function the outputs of the slaves can be tested. 1.

Safety Monitors - AS-i Quick Reference - 08/2014 26 3.9 Diagnostics of slaves in Safety Monitor 1. Press OK-button 2. Select DIAGNOSIS and pre

Safety Monitors - AS-i Quick Reference - 08/2014 27 3.10 Cable pin configuration for GMOX Pinning: Sub Min D 9 PS/2 Connector 2 1 3 2 5 3 and 5

Safety Monitors - AS-i Quick Reference - 08/2014 28 3.11 Fatal Errors List of „Fatal Errors“ in SMOx und GMOx devices Fatal Error Comment Help 154

Safety Monitors - AS-i Quick Reference - 08/2014 29 Hint to „Fault at semiconductor output “ There are several possible reasons for getting this fa

Safety Monitors - AS-i Quick Reference - 08/2014 3 1 EUCHNER Safety Parts 1.1 Parameters for all EUCHNER electromechanical safety switches, non-co

Safety Monitors - AS-i Quick Reference - 08/2014 30 3. Select AS-I MASTER and press OK-button 4. Select AS-i CIRCUIT 1 and press OK-button 5.

Safety Monitors - AS-i Quick Reference - 08/2014 31 4 Software ASiMon 4.1 Diagnostics with Software ASiMon Display Colour Meaning green, contin

Safety Monitors - AS-i Quick Reference - 08/2014 32 4.2 State of AS-i Safety Switches GP, NZ, NX, SGP Programming: dual channel dependent Sta

Safety Monitors - AS-i Quick Reference - 08/2014 33 CET, TP, STP, STA, TZ, BI, all AS1 Programming: dual channel conditionally dependent State Mo

Safety Monitors - AS-i Quick Reference - 08/2014 34 CES Programming: dual channel dependent, Synchronization time 0,5s State Monitor diagnostics Do

Safety Monitors - AS-i Quick Reference - 08/2014 4 1.2 Failure programming an AS-i address of EUCHNER safety switch With a Schneider AS-i address

Safety Monitors - AS-i Quick Reference - 08/2014 5 1.3 States of ASi safety parts LED State Description ASI green Fault or State red on off Nor

Safety Monitors - AS-i Quick Reference - 08/2014 6 2 SFM Safety Monitor 2.1 Password forgotten or lost Read-out of the configuration from a monit

Safety Monitors - AS-i Quick Reference - 08/2014 7 2.2 Delete Safety Monitor A configured safety monitor can be deleted by the following method:

Safety Monitors - AS-i Quick Reference - 08/2014 8 2.3 Replacing a defective Slave (without teach-in of actuator) All safety slaves without necessi

Safety Monitors - AS-i Quick Reference - 08/2014 9 2.4 Replacing a defective Slave (with teach-in of actuator) All safety slaves with necessity for